The Philips IntelliVue M3001A (Option A01C06) is the extended-measurement configuration of the IntelliVue Multi-Measurement Module with Philips FAST SpO2. Building on the A01 standard package — ECG, arrhythmia, ST, respiration, FAST SpO2, and oscillometric NBP — the C06 option adds a combined invasive pressure and temperature connector, enabling the module to support either invasive blood pressure monitoring or temperature measurement in addition to the full core parameter set. This makes the A01C06 the most clinically complete single-MMS configuration available without adding 12-lead ECG, and the module most commonly deployed in ICU, step-down, and critical care transport environments where arterial line monitoring or core temperature tracking is routinely required. As with all M3001A variants, patient demographics, trend data, and measurement settings are stored in the module itself and travel with the patient between IntelliVue host monitors.

Part Number / Option
M3001A, Option A01C06

Parameters Monitored
ECG (3/5-lead), Arrhythmia, ST, Respiration, Philips FAST SpO2, NBP (oscillometric), Invasive Pressure OR Temperature (shared port — not simultaneous)

SpO2 Technology
Philips FAST SpO2 — compatible with Nellcor OxiMax sensors

IBP / Temp Port
One combined connector — supports invasive pressure transducer OR temperature probe; pressure and temperature cannot be used simultaneously on this port

Host Monitor Compatibility
IntelliVue MP20/30/40/50/60/70/80/90; MX-series; M3046A (M/M4)

Data Storage
Up to 8 hrs of trend data at 1-min resolution stored in module; retained 6 hrs while disconnected

IPR Medical buys, sells, repairs, and stocks parts for the Philips IntelliVue M3001A. Contact us at 855-477-8866 or cs@iprmed.com.

The Philips IntelliVue M3001A (Option A01C12) is the 12-lead ECG configuration of the IntelliVue Multi-Measurement Module with Philips FAST SpO2. Building on the A01 standard package — ECG, arrhythmia, ST, respiration, FAST SpO2, and oscillometric NBP — the C12 option adds conventional 12-lead ECG capture capability and EASI-derived 12-lead ECG using only 5 electrodes. The A01C12 is the correct choice for facilities that require diagnostic-quality 12-lead ECG at the bedside alongside continuous monitoring but do not need invasive pressure or temperature measurement in the MMS module itself. It is widely deployed in step-down units, telemetry floors, cardiac monitoring environments, and pre-/post-procedure areas where 12-lead ECG documentation is a standard clinical workflow. As with all M3001A variants, patient demographics, trend data, and measurement settings are stored within the module and travel with the patient between IntelliVue host monitors.

Part Number / Option
M3001A, Option A01C12

Parameters Monitored
ECG (3/5/12-lead), EASI ECG, Arrhythmia, ST (up to 12-lead), QT/QTc, Respiration, Philips FAST SpO2, NBP (oscillometric)

SpO2 Technology
Philips FAST SpO2 — compatible with Nellcor OxiMax sensors

12-Lead ECG
Yes — conventional 12-lead capture with diagnostic signal quality (ANSI/AAMI EC11); EASI 12-lead using 5 electrodes also supported

Invasive Pressure / Temperature
Not included in Option A01C12 — available with Option A01C18

Host Monitor Compatibility
IntelliVue MP20/30/40/50/60/70/80/90; MX-series; M3046A (M/M4)

Data Storage
Up to 8 hrs of trend data at 1-min resolution stored in module; retained 6 hrs while disconnected

IPR Medical buys, sells, repairs, and stocks parts for the Philips IntelliVue M3001A. Contact us at 855-477-8866 or cs@iprmed.com.

The Philips IntelliVue M3001A (Option A02C06) is the extended-measurement configuration of the IntelliVue Multi-Measurement Module for facilities standardized on Nellcor OxiMax sensors. Building on the A02 standard package — ECG, arrhythmia, ST, respiration, Nellcor OxiMax-compatible SpO2, and oscillometric NBP — the C06 option adds a combined invasive pressure and temperature connector, enabling the module to support either invasive blood pressure monitoring or temperature measurement in addition to the full core parameter set. The A02C06 is the OxiMax-sensor equivalent of the A01C06, delivering an identical clinical measurement footprint while using a dedicated OxiMax-compatible SpO2 interface in place of the Philips FAST SpO2 circuit. This configuration is widely deployed in ICU, cardiovascular step-down, post-anesthesia care, and critical care transport environments where arterial line monitoring or core temperature tracking is routinely required alongside a Nellcor OxiMax sensor fleet. As with all M3001A variants, patient demographics, trend data, and measurement settings are stored in the module itself and travel with the patient between IntelliVue host monitors.

Part Number / Option
M3001A, Option A02C06

Parameters Monitored
ECG (3/5-lead), Arrhythmia, ST, Respiration, Nellcor OxiMax SpO2, NBP (oscillometric), Invasive Pressure OR Temperature (shared port — not simultaneous)

SpO2 Technology
Nellcor OxiMax-compatible — requires M1943NL adapter cable for OxiMax sensor connection

IBP / Temp Port
One combined connector — supports invasive pressure transducer OR temperature probe; pressure and temperature cannot be used simultaneously on this port

Host Monitor Compatibility
IntelliVue MP20/30/40/50/60/70/80/90; MX-series; M3046A (M/M4)

Data Storage
Up to 8 hrs of trend data at 1-min resolution stored in module; retained 6 hrs while disconnected

IPR Medical buys, sells, repairs, and stocks parts for the Philips IntelliVue M3001A. Contact us at 855-477-8866 or cs@iprmed.com.

The Philips IntelliVue M3001A (Option A02C12) is the 12-lead ECG configuration of the IntelliVue Multi-Measurement Module for facilities standardized on Nellcor OxiMax sensors. Building on the A02 standard package — ECG, arrhythmia, ST, respiration, Nellcor OxiMax-compatible SpO2, and oscillometric NBP — the C12 option adds conventional 12-lead ECG capture and EASI-derived 12-lead ECG using only 5 electrodes. The A02C12 is clinically identical to the A01C12 in every respect except that the SpO2 interface uses a dedicated OxiMax-compatible circuit rather than Philips FAST SpO2, and OxiMax sensors connect through the M1943NL adapter cable rather than directly to the module’s SpO2 port. It is the correct choice for facilities that require documented, diagnostic-quality 12-lead ECG recordings alongside continuous monitoring and are standardized on Nellcor OxiMax sensors, but do not need invasive pressure or temperature within the MMS module itself.

Part Number / Option
M3001A, Option A02C12

Parameters Monitored
ECG (3/5/12-lead), EASI ECG, Arrhythmia, ST (up to 12-lead), QT/QTc, Respiration, Nellcor OxiMax SpO2, NBP (oscillometric)

SpO2 Technology
Nellcor OxiMax-compatible — requires M1943NL adapter cable for OxiMax sensor connection

12-Lead ECG
Yes — conventional 12-lead capture with diagnostic signal quality (ANSI/AAMI EC11); EASI 12-lead using 5 electrodes also supported

Invasive Pressure / Temperature
Not included in Option A02C12 — available with Option A02C18

Host Monitor Compatibility
IntelliVue MP20/30/40/50/60/70/80/90; MX-series; M3046A (M/M4)

Data Storage
Up to 8 hrs of trend data at 1-min resolution stored in module; retained 6 hrs while disconnected

IPR Medical buys, sells, repairs, and stocks parts for the Philips IntelliVue M3001A. Contact us at 855-477-8866 or cs@iprmed.com.

The Philips IntelliVue M3001A (Option A03C06) is the extended-measurement configuration of the IntelliVue Multi-Measurement Module for facilities standardized on Masimo LNCS sensors. Building on the A03 standard package — ECG, arrhythmia, ST, respiration, Masimo SET SpO2, and oscillometric NBP — the C06 option adds a combined invasive pressure and temperature connector, enabling the module to support either invasive blood pressure monitoring or temperature measurement in addition to the full core parameter set. The A03C06 is the Masimo SET equivalent of the A01C06 and A02C06, delivering an identical clinical measurement footprint while using a dedicated Masimo SET SpO2 interface and requiring the Masimo LNC MP-10 dual-key patient cable for sensor connection. This configuration is widely deployed in ICU, cardiovascular step-down, post-anesthesia care, and critical care transport environments where arterial line monitoring or core temperature tracking is standard practice alongside a Masimo LNCS sensor fleet. As with all M3001A variants, patient demographics, trend data, and measurement settings are stored in the module itself and travel with the patient between IntelliVue host monitors.

Part Number / Option
M3001A, Option A03C06

Parameters Monitored
ECG (3/5-lead), Arrhythmia, ST, Respiration, Masimo SET SpO2, NBP (oscillometric), Invasive Pressure OR Temperature (shared port — not simultaneous)

SpO2 Technology
Masimo SET — requires Masimo LNC MP-10 dual-key patient cable (part 2281) for LNCS sensor connection

IBP / Temp Port
One combined connector — supports invasive pressure transducer OR temperature probe; pressure and temperature cannot be used simultaneously on this port

Host Monitor Compatibility
IntelliVue MP20/30/40/50/60/70/80/90; MX-series; M3046A (M/M4)

Data Storage
Up to 8 hrs of trend data at 1-min resolution stored in module; retained 6 hrs while disconnected

IPR Medical buys, sells, repairs, and stocks parts for the Philips IntelliVue M3001A. Contact us at 855-477-8866 or cs@iprmed.com.

The Philips IntelliVue M3001A (Option A03C12) is the 12-lead ECG configuration of the IntelliVue Multi-Measurement Module for facilities standardized on Masimo LNCS sensors. Building on the A03 standard package — ECG, arrhythmia, ST, respiration, Masimo SET SpO2, and oscillometric NBP — the C12 option adds conventional 12-lead ECG capture and EASI-derived 12-lead ECG using only 5 electrodes. The A03C12 is the Masimo SET equivalent of the A01C12 and A02C12: clinically identical in 12-lead ECG capability and overall parameter set, with the SpO2 interface built around a dedicated Masimo SET circuit, and Masimo LNCS sensors connecting via the Masimo LNC MP-10 dual-key patient cable (part 2281). It is the correct choice for facilities that require documented, diagnostic-quality 12-lead ECG recordings alongside continuous monitoring and are standardized on Masimo LNCS sensors, but do not need invasive pressure or temperature within the MMS module itself.

Part Number / Option
M3001A, Option A03C12

Parameters Monitored
ECG (3/5/12-lead), EASI ECG, Arrhythmia, ST (up to 12-lead), QT/QTc, Respiration, Masimo SET SpO2, NBP (oscillometric)

SpO2 Technology
Masimo SET — requires Masimo LNC MP-10 dual-key patient cable (part 2281) for LNCS sensor connection

12-Lead ECG
Yes — conventional 12-lead capture with diagnostic signal quality (ANSI/AAMI EC11); EASI 12-lead using 5 electrodes also supported

Invasive Pressure / Temperature
Not included in Option A03C12 — available with Option A03C18

Host Monitor Compatibility
IntelliVue MP20/30/40/50/60/70/80/90; MX-series; M3046A (M/M4)

Data Storage
Up to 8 hrs of trend data at 1-min resolution stored in module; retained 6 hrs while disconnected

IPR Medical buys, sells, repairs, and stocks parts for the Philips IntelliVue M3001A. Contact us at 855-477-8866 or cs@iprmed.com.